Micrel, Inc.
MIC2085/2086
 
 
May 2006 
21
M9999-050406
(408) 955-1690
 
Auto-Retry Upon Overcurrent Faults
The MIC2085/86 can be configured for automatic restart
after a fault condition. Placing a diode between the ON
and/FAULT pins, as shown in Figure 9, will enable the
auto-restart   capability   of   the   controller.   When   an
application is configured for auto-retry, the overcurrent
timer should be set to minimize the duty cycle of the
overcurrent response to prevent thermal runaway of the
power MOSFET. See MOSFET Transient Thermal
Issues section for further detail. A limited duty cycle is
achieved when the overcurrent timer duration (t
OCSLOW
) is
much less than the start-up delay timer duration (t
START
)
and is calculated using the following equation:
 
100%
t
t
Cycle
Duty
Retry
Auto
START
OCSLOW
?/DIV>
=

  (10)
An InfiniBand" Application Circuit
The   circuit   in   Figure   10   depicts   a   single   50W
InfiniBand" module using the MIC2085 controller. An
InfiniBand" backplane distributes bulk power to multiple
plug-in modules that employ DC/DC converters for local
supply requirements. The circuit in Figure 10 distributes
12V from the backplane to the MIC2182 DC/DC
converter that steps down +12V to+3.3V for local bias.
The pass transistor, Q1, isolates theMIC2182s input
capacitance during module plug-in and allows the
backplane to accommodate additional plug-in modules
without affecting the other modules on the backplane.
The two control input signals are VBxEn_L (active LOW)
and a Local Power Enable (active HIGH). The MIC2085
in the circuit of Figure 10 performs a number of
functions. The gate output of Q1 is enabled by the two
bit input signal VBxEn_L, Local Power Enable = [0,1].
Also, the MIC2085 limits the drain current of Q1 to 7A,
monitors VB_In for an overvoltage condition greater than
16V, and enables the MIC2182 DC/DC converter
downstream   to   supply   a   local   voltage   rail.   The
uncommitted comparator is used to monitor VB_In for an
undervoltage condition of less than 10V, indicated by a
logic LOW at the comparator output (COMPOUT).
COMPOUT may be used to control a downstream
device such as another DC/DC converter. Additionally,
the MIC2085 is configured for auto-retry upon an
overcurrent fault condition by placing a diode (D1)
between the /FAULT and ON pins of the controller.
 
 
 
Figure 9. Auto-Retry Configuration
 
 
相关PDF资料
MIC2225-4OYMT TR IC REG DL BUCK/LINEAR 10TMLF
MIC2310-2ZTS TR IC HOT SWAP CTLR 2CHAN 24TSSOP
MIC2341-2YTQ IC HOT PLUG CTLR DUAL PCI 48TQFP
MIC2569YQS TR IC POWER SWITCH CABLECARD 16QSOP
MIC2583R-MBQS TR IC CTRLR HOT SWAP 200MV 16-QSOP
MIC2585-2MBTS TR IC CTRLR HOT SWAP DUAL 24-TSSOP
MIC2586R-2BM TR IC CTRLR/SEQ HOT SWAP 14-SOIC
MIC2587R-2BM TR IC CTRLR HOT SWAP POS HV 8-SOIC
相关代理商/技术参数
MIC2086-XBQS 制造商:MICREL 制造商全称:Micrel Semiconductor 功能描述:Single Channel Hot Swap Controllers
MIC2090 制造商:MICREL 制造商全称:Micrel Semiconductor 功能描述:Current Limiting Power Distribution Switches
MIC2090_11 制造商:MICREL 制造商全称:Micrel Semiconductor 功能描述:Current Limiting Power Distribution Switches
MIC2090-1YM5 制造商:MICREL 制造商全称:Micrel Semiconductor 功能描述:Current Limiting Power Distribution Switches
MIC2090-1YM5 TR 功能描述:电源开关 IC - USB 50mA Current Limiting Power Distribution Switch RoHS:否 制造商:Micrel 电源电压-最小:2.7 V 电源电压-最大:5.5 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:SOIC-8 封装:Tube
MIC2090-1YM5TR 制造商:Micrel 功能描述:Power Switch 50mA 1.8 5.5V 5 Pin SOT23
MIC2090-1YM5-TR 功能描述:IC DISTRIBUTION SW 50MA SOT-23-5 制造商:microchip technology 系列:- 包装:剪切带(CT) 零件状态:有效 开关类型:通用 输出数:1 比率 - 输入:输出:1:1 输出配置:高端 输出类型:P 通道 接口:开/关 电压 - 负载:1.8 V ~ 5.5 V 电压 - 电源(Vcc/Vdd):不需要 电流 - 输出(最大值):50mA 导通电阻(典型值):700 毫欧 输入类型:非反相 特性:状态标志 故障保护:限流(固定),超温,反向电流,UVLO 工作温度:-40°C ~ 125°C (TJ) 封装/外壳:SC-74A,SOT-753 供应商器件封装:SOT-23-5 标准包装:1
MIC2090-2YM5 制造商:MICREL 制造商全称:Micrel Semiconductor 功能描述:Current Limiting Power Distribution Switches